Woods-powr-grip MRPT89DC Manuel d'utilisateur

KEEP FOR FUTURE REFERENCE INSTRUCTIONS International Version MODEL NUMBER: MRPT89DC(O) SERIAL NUMBER: ___________ (please see serial label and r

Rev 24.0/12-13 8 MRPT89DC: #35062 INTENDED USE LOAD CHARACTERISTICS WARNING: This lifter is NOT intended for lifting hazardous materials, such as

Rev 24.0/12-13 9 MRPT89DC: #35062 OPERATING ENVIRONMENT The operator must determine whether the lifter is intended to be used in each work environme

Rev 24.0/12-13 10 MRPT89DC: #35062 OPERATION BEFORE USING THE LIFTER The operator must determine whether the lifter is capable of performing each i

Rev 24.0/12-13 11 MRPT89DC: #35062 TO APPLY THE PADS TO A LOAD Powering up the Lifter Place the power switch in the ON position ( ) (blue indica

Rev 24.0/12-13 12 MRPT89DC: #35062 Note: If a vacuum pad has been lying against a hard object (as during shipping), it may be slightly distorted.

Rev 24.0/12-13 13 MRPT89DC: #35062 TO LIFT AND MOVE THE LOAD WARNING: Lift bar must be oriented vertically to lift load. Load Capacity and the Lift

Rev 24.0/12-13 14 MRPT89DC: #35062 In Case of Power Failure The lifter is equipped with a vacuum reserve tank, designed to maintain vacuum temporari

Rev 24.0/12-13 15 MRPT89DC: #35062 TO RELEASE THE PADS FROM THE LOAD WARNING: Load must be fully supported before releasing vacuum pads. When the l

Rev 24.0/12-13 16 MRPT89DC: #35062 MAINTENANCE WARNING: Always make sure battery is disconnected before servicing lifter. Note: One or more wirin

Rev 24.0/12-13 17 MRPT89DC: #35062 • Keep a written record of all Periodic Inspections. If any deficiency is detected during the inspection, correct

Rev 24.0/12-13 18 MRPT89DC: #35062 BATTERY TEST The lifter is equipped with a battery gauge to help the operator evaluate whether the battery has ad

Rev 24.0/12-13 19 MRPT89DC: #35062 BATTERY RECHARGE CAUTION: Charge battery only while lifter’s power switch is in the OFF ( ) position. Operat

Rev 24.0/12-13 20 MRPT89DC: #35062 VACUUM PAD MAINTENANCE Friction Coefficient The friction coefficient represents the lifter's ability to resi

Rev 24.0/12-13 21 MRPT89DC: #35062 WARNING: Never use unauthorized rubber cleaners or conditioners to clean vacuum pad. To prevent liquid from cont

Rev 24.0/12-13 22 MRPT89DC: #35062 AIR FILTER MAINTENANCE − LARGE (for 4.4 oz [130 ml] bowl size filters) Filter Function and Conditions Requiring S

Rev 24.0/12-13 23 MRPT89DC: #35062 VACUUM PUMP MAINTENANCE − DYNAFLO DV1032102 WARNING: Before proceeding with any maintenance, disconnect power so

Rev 24.0/12-13 24 MRPT89DC: #35062 VACUUM PUMP MAINTENANCE ― THOMAS 2907CDC22/12 WARNING: Before proceeding with any maintenance, disconnect power

Rev 24.0/12-13 25 MRPT89DC: #35062 VACUUM SWITCH ADJUSTMENT Vacuum Switch Function A vacuum switch controls the vacuum pump and the vacuum lift ligh

Rev 24.0/12-13 26 MRPT89DC: #35062 Adjustment Procedure WARNING: Load capacity decreases whenever vacuum switch is adjusted to maintain lower vacuu

Rev 24.0/12-13 27 MRPT89DC: #35062 LINEAR TILT ACTUATOR Since the tilt actuator is prelubricated, no additional lubrication is required under normal

Rev 24.0/12-13 1 MRPT89DC: #35062 TABLE OF CONTENTS SPECIFICATIONS ...

Rev 24.0/12-13 28 MRPT89DC: #35062 REPLACEMENT PARTS LIST Stock No. Description Qty. 93220 Vacuum Pump - Diaphragm Type - 1-SCFM [28 liters/minute]

Rev 24.0/12-13 29 MRPT89DC: #35062 LIMITED WARRANTY Powr-Grip products are carefully constructed, thoroughly inspected at various stages of product

Rev 24.0/12-13 30 MRPT89DC: #35062

Rev 24.0/12-13 31 MRPT89DC: #35062

Rev 24.0/12-13 32 MRPT89DC: #35062

Rev 24.0/12-13 33 MRPT89DC: #35062

Rev 24.0/12-13 34 MRPT89DC: #35062

Rev 24.0/12-13 35 MRPT89DC: #35062

Rev 24.0/12-13 2 MRPT89DC: #35062 MAINTENANCE SCHEDULE ...

Rev 24.0/12-13 3 MRPT89DC: #35062 SPECIFICATIONS Model Number: MRPT89DC(O) Description: Designed for use with a crane or other hoisting equipment,

Rev 24.0/12-13 4 MRPT89DC: #35062 WARNINGS Powr-Grip is pleased to offer the most reliable vacuum lifters available. Despite the high degree of se

Rev 24.0/12-13 5 MRPT89DC: #35062 OPERATING FEATURES Note: Components featured in the following instructions for assembling, operating or maintain

Rev 24.0/12-13 6 MRPT89DC: #35062 ASSEMBLY 1) Open the shipping container and remove all materials for restraining or protecting the vacuum lifter

Rev 24.0/12-13 7 MRPT89DC: #35062 PAD FRAME OPTIONS The following illustrations show which Pad Spread dimensions are possible for the lifter when eq