Woods-powr-grip N4000DGT Manuel d'utilisateur télécharger pdf

SPECIFICATIONS

Product Description

The Deglazing Tool uses a vacuum cup and lever to pry nonporous materials,

such as mirrors and windows from its installation point as follows: A manual

pump removes air from between a rubber pad and the contact surface; a red

line on the pump’s plunger serves as a vacuum indicator; check valve allows

the user to repump the pad without removing it from the contact surface; and

a release mechanism allows the pad to disengage completely. A pry bar and

pressure pad provide leverage to pull the material from its installation point.

Environmental Conditions

Use on clean, relatively smooth, nonporous surfaces, at temperatures from 10°

to 120° Fahrenheit [-12° to 49° Celsius]. Moisture or contaminants can reduce

the slip resistance of a vacuum pad. A red-line indicator may not perform

reliably at elevations above 5000 feet [1524 meters]; see MAINTENANCE:

Service.

ASSEMBLY and SET-UP

1) The Deglazing Tool comes fully assembled and ready to use.

Note: An optional 18-inch [45.8 cm] wide-base pressure pad can replace the

standard 4¼-inch [10.8 cm] pressure pad by removing the cotterless hitch

pin, exchanging the pressure pads and replacing the cotterless hitch pin.

Using the wide-based pressure pad allows the pressure to be distributed

over a larger surface area, preferably over more than one stud or support

beam.

OPERATION

To Attach

1) Clean the mounting surface and, if needed, the face of the vacuum pad (see

MAINTENANCE: Cleaning).

CAUTION: Test the Vacuum Pad and Pressure Pad for staining or

deformation on surfaces with light colors or soft coatings.

2) Orient the pressure pad over a stud in the wall or at a location which will not

bend, depressed or otherwise become damaged by the pressure resulting

from prying on the handle.

3) Position the vacuum pad on the nonporous surface close to the adhesive

or mastic location by loosening the thumb screw and sliding the vacuum

cup along the bar and tighten the thumbscrew. Make sure the plunger

can be seen by the operator, in case the red line should appear while the

Deglazing Tool is in use.

4) Pump the plunger until the vacuum pad attaches completely and the red

line is hidden. The Deglazing Tool is now ready for use. Check the plunger

frequently to make sure the vacuum cup remains securely attached. If a

red line appears, pump the plunger until the red line is hidden again (see

WARNINGS).

5) Pull on the pry bar with increasing pressure until the adhesive or mastic

begins to let go.

Note: Jerking on the pry bar may cause the rapid release of the adhesive or

mastic resulting in damage to the product or injury to the operator.

5) Reposition the pressure pad and vacuum cup as necessary to completely

remove the object from its xture.

To Release

1) Secure the Deglazing Tool, to prevent it from falling when the vacuum cup

is released.

2) Use the vacuum release mechanism to disengage the vacuum cup: press

the valve release lever until the vacuum cup disengages completely.

MAINTENANCE

Service

Since aging and wear reduce the capacity of the rubber vacuum pad, it should

be replaced at least once every 2 years or whenever damage is discovered

(see Inspection).

If the vacuum cup does not function normally (see Inspection), the face of a

vacuum pad may be dirty or the vacuum cup may require service. First clean

the pad face according to the directions to follow. If the condition persists,

contact an authorized dealer or visit www.powrgrip.com for assistance.

Cleaning

1) Remove the air lter from the face of the vacuum pad.

2) Use a clean sponge or lint-free cloth to apply soapy water or another mild

cleanser to the pad face; see WARNINGS and www.powrgrip.com for more

information. CAUTION: To prevent liquid from contaminating the pump,

hold the pad face-down or cover the suction hole in the lter recess.

3) Wipe all residue from the pad face.

4) Allow the pad to dry and reinstall the air lter.

Inspection

Examine and test the vacuum cup regularly to make sure it does not exhibit

the following faults:

• cuts or damage to sealing edges of rubber pad.

• cracks or dents in handle, weldment or pump.

• red line appears soon after attaching the vacuum cup.

• sluggishness or dramatic changes in pump action.

• excessive glaze or stiffness of rubber vacuum pad.

• air lter missing from pad face.

Correct any faults before using the Deglazing Tool (see Service).

Storage

Store the Deglazing Tool in a clean, dry location out of direct sunlight. Protect

the vacuum pad from damage using the cover or another appropriate means.

WARNINGS

Failure to observe WARNINGS could damage the devise, or cause injury to

the user.

• Never place the face of a vacuum pad against surfaces which could damage

a sealing edge.

PARTS

1 90154 Plunger Assembly, ABS

2 49486T Rubber Vacuum Pad, 8” Dia.,

Flat (G0695)

3 Red Line Vacuum Indicator

4 10002 Screw, 1/4-20 x 1/2” Pan Head

Phillips Machine Screw

5 90151 Handle / Valve Assembly, ABS

6 Vacuum Valve Release Lever

7 Handle Grip - 1” ID

8 30” Pry Bar

9 10080 ¼-20 x ½” Thumb Screw

10 13512 3/8” x 2” Cotterless Hitch Pin

11 13520 3/8” x 3” Cotterless Hitch Pin

12 4¼” Pressure Pad (Standard)

13 18” Wide-Base Pressure Pad

(Optional)

Deglazing Tool

Instructions for Use,

Maintenance and Care

Rev. 0.0 / 06-10 Instruction Sheet: DGLAZER

P.O. Box 368 - 908 West Main 1.800.548.7341 Fax: 1-406-628-8354

Laurel, MT 59044 U.S.A. 1.406.628.8231 www.powrgrip.com

Products are manufactured under an

ISO 9001 quality management system

1 2

Deglazing Tool 1
Limited Warranty 2

Résumé du contenu

Page 1 - Deglazing Tool

SPECIFICATIONSProduct DescriptionThe Deglazing Tool uses a vacuum cup and lever to pry nonporous materials, such as mirrors and windows from its insta

Page 2 - Limited Warranty

• Always avoid conditions that could cause a vacuum pad to slip or to disengage prematurely, such as: contaminants, cuts or scratc

Commentaires sur ces manuels

Pas de commentaire

Woods-powr-grip N4000DGT Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Hoist Woods-powr-grip N4000DGT. Wood’s Powr-Grip N4000DGT User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Hoist Woods-powr-grip N4000DGT